• 2021-09-14

The rapid development of science and technology brings about the improvement of production level. With the rapid development of industry, advanced metal stamping technology has been widely used in our country. Now let's talk about what metal stamping is and its advantages: 1、 What is metal stamping Metal stamping is a processing method of cutting and forming metal plate or coil by using punch and ...

• 2021-11-27

Material selection of stamping parts: The three most important steps in a stamping factory are shearing, punching / cutting and folding. Stamping parts are sometimes used as metal pulling. The word comes from English platemetal. Generally, some metal sheets are pressed by hand or die to produce plastic deformation to form the desired shape and size, and more complex parts can be formed by welding ...

• 2021-12-10

In terms of structure, the convenience of feeding, ordering, discharging and waste cleaning shall be ensured as far as possible. For the processing of small parts, it is strictly prohibited for the operator's fingers, wrists or other parts of the body to extend into the mold area for operation; For the processing of large parts, if the operator has to work in the mold by hand, the scope of enterin...

• 2021-12-18

At present, the commonly used materials of metal stamping parts are: 1) SECC: galvanized iron sheet 2) Spec: tinned cold rolled sheet 3) Sus: stainless steel series 4) Al: aluminum series 5) Cu: copper series 6) PBR: white copper 7) Spte: Tinplate 8) Al set: lamp cover 9) Al Arg: lamp cover

• 2021-12-30

Stamping process and its characteristics stamping is a pressure processing method that uses the die installed on the press to exert pressure on the material at room temperature to produce separation or plastic deformation, so as to obtain the required parts. Stamping is usually cold deformation processing of materials at room temperature, and mainly uses sheet metal to process the required parts, ...

• 2022-01-04

Hardware stamping factory has strict inspection standards, which are divided into sampling inspection and all inspection. Sampling inspection, also known as sampling inspection, is a statistical method and theory to randomly select a small number of products (samples) from a batch of products for inspection, so as to judge whether the batch of products are qualified or not. It is different from co...

• 2022-01-15

Metal processing plants often encounter burrs in metal stamping parts when producing metal stamping products. There are tools to remove the burr of metal stamping parts: 1. Hole: use a chamfering knife or the front end of a larger diameter drill bit 2. Edge: use file, oilstone, sandpaper, grindstone, 3. Welding slag: vibration slag removal tools can also remove brittle burrs 4. Outer diameter: gui...

• 2022-01-22

Product introduction: Material: stainless steel, red copper, phosphor copper, SECC, SGCC, SPCC, cold rolling, hot rolling Production process: press installation, specific die stamping, appearance treatment (electroplating, powder                                   spraying, heat treatment, pickling passivation...

• 2022-02-23

The quality standards of stamping parts are divided into national standard and non-standard. The following are different concepts about national standard and non-standard: National standard: refers to the standard approved and issued by the national standardization authority, which is of great significance to the national economic and Technological Development and is unified throughout the country...

• 2022-03-04

The processing of metal stamping parts is the requirements for bending parts: 1. The shape of bending parts shall be symmetrical as far as possible, and the bending radius shall not be less than the minimum bending radius allowed by the material. 2. The curved edge is too short and difficult to form, so make the straight part of the curved edge H > 2 δ。 If h is required to be very short, approp...

• 2022-03-09

1: Electroplating The process of attaching a metal film to the surface of metal by electrolysis to prevent corrosion A technology that can improve weldability, conductivity and beauty. Usually electroplated with gold, silver, nickel, zinc and tin. 2: Anodic oxidation It is mainly the anodizing of aluminum, which uses the electrochemical principle to generate a layer of alumina film on the surface ...

• 2022-04-08

Why is the surface quality of metal stamping parts poor? There are many reasons for the surface quality problems of stamping parts. For example, the surface quality of coil, sheet and die will affect the quality of stamping parts. The operation in the stamping process and the clamping, taking and unloading of station instruments may also damage the surface quality of stamping parts. Therefore, the...